Skip to content
Spray foam and insulation services for Clayton and Contra Costa County
Blown-in insulation installed at measured depth in a Clayton attic

Home / Services / Blown-In Insulation

Residential & Commercial

Blown-In Insulation in Clayton, CA

Blown-in fiberglass and cellulose for attic floors and retrofit walls, installed to a measured depth across the Contra Costa corridor.

Blown-in insulation is the workhorse of attic upgrades in Clayton. It flows over and around ceiling joists, wiring, duct chases and the odd framing details that make batt insulation leave gaps, and it installs fast enough to keep the project affordable on larger attic floors. Clayton Spray Foam Insulation installs both blown-in fiberglass and cellulose, and we recommend foam only when the assembly actually calls for it. Spray foam is our flagship, but an open, vented attic floor is often the place where blown-in material delivers the most improvement per dollar in California climate zone 12.

Fiberglass or cellulose

Blown-in fiberglass is made from spun glass fibers, resists moisture absorption and holds its installed depth well over time. Cellulose is made from recycled paper treated for fire resistance, packs more densely and restricts air movement through the material better than fiberglass. Both are proven attic materials. Fiberglass tends to cost a bit more and settles less; cellulose covers irregular framing tightly and performs well at a lower installed cost. We carry both and will tell you plainly which fits your attic and budget.

Depth is the job: R-value explained plainly

R-value is simply a measure of resistance to heat flow: the higher the number, the slower heat moves through the material. For blown-in products, R-value comes from depth, so an attic that needs a higher R-value needs more inches of material, full stop. That is why we install to a measured depth rather than by the bag count or the look of it. Depth markers go in across the attic so you can verify the coverage after the crew leaves, and the written estimate names the target depth before work starts. California's Title 24 energy code sets strong performance expectations for attics in this climate zone, and most of Clayton's older ranch homes carry far less than current targets, while many newer attics along the corridor meet only the minimum.

Top-ups of existing attics

If your attic already has insulation that has settled thin but is still dry and clean, a top-up adds new material over the old to bring the total depth to target. It is one of the most affordable comfort upgrades available for older Clayton homes. Before any top-up we check for two things: air leaks at the ceiling plane, which should be sealed first so the new depth actually performs, and moisture or pest damage in the existing material, which means removal instead of a top-up. Ventilation gets protected too, with baffles at the eaves so the soffit vents stay open under the new depth. See our attic insulation page for the full picture on attic assemblies.

Blown-in for retrofit walls

Older wood-frame ranch homes across Clayton and the Contra Costa corridor often have empty or underfilled wall cavities. Dense-pack blown-in cellulose or fiberglass can fill those walls through small, patchable holes, inside or out depending on the siding, without tearing the house apart. It is the standard retrofit method for walls that were never insulated, and it also helps dampen sound between rooms.

Get a measured, written quote

Every blown-in estimate names the material, the target depth and the square footage covered. Call 712-227-5778 or use the quote form to schedule a free attic or wall inspection anywhere in our service area, including Concord, Walnut Creek, Pleasant Hill, Martinez and Brentwood.

Questions

Common questions

Fiberglass or cellulose: which is better?

Both are solid attic materials. Fiberglass settles less and resists moisture absorption; cellulose packs tighter around framing and usually costs less installed. We install both and recommend based on your attic, not our inventory.

Does blown-in insulation settle over time?

All loose-fill products settle some, cellulose more than fiberglass. We account for settling in the installed depth so the settled result still meets the target R-value named in your estimate.

Can you blow insulation into my existing walls?

Yes. Dense-pack blown-in material fills closed wall cavities through small holes that are patched afterward. It is the standard way to insulate the area's older ranch homes without opening the walls up.

Want to know what your project would cost?

We measure the space and quote the material and depth in writing before any work is scheduled.

Free written estimates • No obligation • Local team

Call Now